2-component primer filler Multi-Fill

Name: 2-component primer filler Multi-Fill
Brand: Würth
SKU: 08932131

Primer filler, 2C Multi-Fill
PRIM-2K-MULTIFILL-400ML

Art.-no. 08932131

EAN 4046778396972

All versions

Similar products

Prices for customers after login

2-component primer filler Multi-Fill

Art.-no. 08932131

Prices for customers after login

Quantity

Exclusively for trade customers

Login/Register
Call customer service:

2-component epoxy primer filler for optimum application safety on all metals, anodised surfaces and GFRP.

Optimal adhesion and corrosion protection properties on bare sheet metal

Excellent insulating action

Can be filled

Long application time

Approx. 4 days at 20°C

Can be covered wet-on-wet

No intermediate sanding once smoothed to a matt finish

Notice

Cannot be used over acid primers. In conjunction with PE spray filler, it is essential that the drying times are observed. After use, turn the can upside down and spray until the valve is empty. Only to be used by skilled professionals.

The usage instructions are recommendations based on the tests we have conducted and are based on our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Product information

Würth Catalogue

Datasheets(X)

Safety data sheet

Certificates/ Documents

Application area

Spot repair and painting parts

Surfaces:

Bare sheet steel

Zinc-plated sheet steel

Aluminium, anodised aluminium

UP filler

Old paints

GRFP materials: Do not use 2-component Multi-Fill with acid primers.

Instructions

The surface must be clean, dry and free from grease. Lightly sand problematic surfaces. Shake the can vigorously for 2 minutes before spraying. Take the push button (red) out of the cover cap, place on the pin on the base of the can and activate by pressing. Remove the push button and dispose of it. Shake the can vigorously again after spraying. Apply 2-3 spray coatings (70 µm) at a distance of 20-30 cm. Observe the intermediate flash-off time (5-15 minutes). Can be painted over with all common top-coat systems.

Drying times

Air drying: 24 hours/20°C

IR drying: 70 minutes/60°C

Oven drying: 30 minutes/60°C

Contents	400 ml
Chemical basis	Epoxy resin
Colour	Beige
Drying time	24 h
Processing time	4 d
Conditions for drying time	at 20°C
Min. flash-off time	10 min
Max. coating thickness	70 µm
Max. temperature resistance	80 °C
Min. spraying distance	20 cm
Max. short-term temperature resistance	120 °C
Min. processing temperature	20 °C
Max. spraying distance	30 cm
Shelf life from production	24 Month

Suitable glove:

Product

Description

Nitrile chemical protective glove With cotton velour finish inside

Description:

Permeation level: 5

Nitrile chemical protective glove Long, heavy-duty design

Description:

Permeation level: 6

Permeation is the process by which a chemical moves through the material of a protective glove on a molecular level. The time from the initial contact between the chemical and the glove to the permeation of the material is the breakthrough time.

Measured breakthrough time

Permeation level

< 10 min

≥ 10 min

≥ 30 min

≥ 60 min

≥ 120 min

≥ 240 min

≥ 480 min

Important information:

The information given is based on experience and laboratory conditions and is designed as a guide. However, the actual suitability of a glove depends on the individual conditions of its use and must be confirmed by an appropriate test under operational conditions. Given the variety of materials and chemicals used, the possibility of incompatibility or usage problems for the wearer cannot be excluded in individual cases. We would be happy to advise you about optimum solutions.