2C plastic adhesive 210sec.
2C plastic adhesive 210
ADH-PLA-2C-210SEC-50ML
REPLAST
Register now and access more than 125,000 products
2-component adhesive for the repair and bonding of many types of plastic
Low number of adhesives to be stored
No H351 (R40) label required
Coarse sanding dust
Fine dust particles are not breathed in
Special shorter mixer nozzle
Less material consumption than with conventional mixers
Quick to harden
Can be sanded and painted over after a very short period of time
High flexibility of the hardened adhesive
Absorbs greater movement and vibration at bumper
Solvent- and silicone-free
Limited adhesion (no constructive adhesives) of PP and PE. Not suitable for PVC, PPS and PTFE. There may be adhesion problems in individual cases due to the coatings and release agents used in some cases in the plastic production process. Observe the work instructions when repairing PP/EPDM. Check material compatibility on a non-visible area if necessary. The product must be stored in a frost-free location.
| Base material | Pre-treatment | Adhesion |
| SMC, BMC, RTM, wood, HPL, PUR-RIM | Sand | Excellent adhesion |
| CFRP (carbon fibre reinforced plastic) | Sand | Excellent adhesion |
| Coated, alloyed metal | In the case of bare metal, the metal should be protected against corrosion | Excellent adhesion |
| PP-EPDM/ ABS | See separate instructions | Good (no structural adhesion) |
The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. We do not assume any liability for a specific application result due to the large number of applications and storage and processing conditions. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.
Repair of spoilers, radiator grills, panel clips, bumpers, brackets on headlights and radiators.
When repairing PP/EPDM (no constructive adhesives), please observe the work instructions.
Bonding of different thermosetting plastics such as CFRP, SMC, BMC, RTM.
Bonding of thermoplastics such as ABS, PC, PUR-RIM.
Bonding of coated metals and wood.
The substrate must be capable of bearing loads and must be clean, dry and free from grease and rust. Old adhesive residues must also be removed. To do so, clean the surface with the plastic cleaner and apply the primer. The flash-off time must be observed. Discard some adhesive before screwing on the mixer nozzle. The first 2 cm of adhesive from the mixer nozzle should also not be used. When applying the adhesive, the mixer should remain in the adhesive to prevent bubbles forming. Observe the work instructions.
Contents | 50 ml |
Container | Double cartridge |
Chemical basis | Two-component polyurethane |
Processing time | 3.5 min |
Colour | Black |
Density | 1.3 g/cm³ |
Min./max. processing temperature | 15 to 25 °C |
Min./max. temperature resistance | -30 to +100 °C |
Solvent-free | Yes |
Silicone-free | Yes |
Shelf life from production/conditions | 24 Month / at 23°C and 50% relative humidity |
Shore D hardness | 79 |
Datasheets(X)
Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2
Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)
Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)
Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.
Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units
Select RAL-colour code
!! NOTE: On-screen visualisation of the colour differs from real colour shade!!
Last viewed
Tapered roller bearing FAG
Twist drill bit HSCo DIN 338 Type RN MFD VARIO
Hexagon Socket Head Cap Screw ISO 4762/DIN 912, steel 8.8, zinc-plated, blue passivated (A2K)
Half-shell hexagon crimping insert
Shoe accessories
Drilling jig for escutcheon fittings
EPS profile thumbturn cylinder
Tungsten carbide bur with MZ teeth
Hexagon Socket Head Cap Screw
LDPE fold masker
