Butyl round cord
Butyl round cord
SEALCORD-BUTYL-D3MM-L50M
Register now and access more than 125,000 products
Excellent compatibility with all familiar surfaces
Good compatibility with metals, concrete, masonry, wood, glass, hard PVC, bitumen, paint systems, as well as extremely good adhesive properties, enables a number of combinations in sealing systems.
Excellent resistance to UV, weathering and water
For both indoor and outdoor use.
Impermeable to vapour diffusion
Self-fusing
Compatible with Plexiglas and Macrolon
The usage instructions are recommendations based on the tests we have conducted and on our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. If our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee the consistent quality of our products. We reserve the right to make technical changes and further develop products. Please observe the technical data sheet!
The self-fusing butyl round cord has high adhesive strength, and boasts excellent insulating and moisture-resistant properties. The tape has good compatibility with metals, concrete, masonry, wood, glass, hard PVC, bitumen and painting systems. The very good adhesion properties enable a diverse combination in sealing systems. Ideally suited for mounting parts in the automotive sector, e.g. bonding lower door cladding films, attaching trim panels or sealing storage tanks, silos, trapezoidal plate roofs and similar items to prevent vibrations. Suitable for all overlapping sealing applications for assembly parts in the automotive and roof area, façade and equipment construction, in the furniture and interior construction industry, in sanitary and electrical installation as well as all similar applications such as involving grommets, sleeves, cable end caps or similar components.
Application instructions: The surfaces to be sealed must be dry, capable of bearing load and free from grease and dust. The application temperature should not be below +5°C. Absorbent and porous surfaces must be pre-treated with Würth butyl/bitumen primer. The butyl tape cord must be carefully pushed onto the surface. Pressing the sealing surfaces together results in a perfect seal. Butyl has a "cold flow" tendency (flow characteristic of the tape) Butyl products should therefore always be secured mechanically, e.g. screwing the parts, applying a press-on profile. When using a press-on profile, the profile manufacturer's specifications regarding the width of the butyl tape must be observed. Using excessive contact pressure on the profile will cause the sealing compound to be "pushed out". Never compress butyl products absolutely flat (use the supplied disc as a spacer)
Chemical basis | Butyl natural rubber |
Colour | Black |
Number of cords | 5 PCS |
Outer diameter | 3 mm |
Length | 50 m |
Min./max. processing temperature | 5 to 30 °C |
Min./max. temperature resistance | -40 to 100 °C |
Max. short-term temperature resistance | 150 °C |
Density/conditions | 1.7 g/cm³ / in accordance with DIN EN ISO 1183-1 |
Building material class/conditions | B2 - Normally inflammable / in accordance with DIN 4102 |
Shore hardness OO / conditions | 50 / in accordance with DIN EN ISO 868 |
Dynamic peel strength at 25 mm | 30 N |
Min. compressive strength / conditions | 0.08 / NF P30-303 |
Shelf life from production/conditions | Unlimited / dry, lying, dust-free storage area, 20°C and 50% relative humidity |
Ultraviolet resistance | Very good |
Resistance against | Weather, Humidity, UV radiation |
Datasheets (0)
Certificates/ Documents (0)
Last viewed
High-visibility jacket
Pair of clamping jaws
Hand cleaner in tub
Single-handed grease gun With variable pressure setting directly on handle
Clamping pin/clamping sleeve
Work dungarees
Threaded pin ISO 4027, steel, 45H, plain
Pan head screw with H cross recess DIN 7985, steel 4.8, zinc-plated, blue passivated (A2K)
EPS profile thumbturn cylinder for keyed alike systems with original equipment
Twist drill bit HSCo DIN 1869 R3 type RN
