CERAfix<SUP>®</SUP> 412 C2 FT E Flex Plus tile adhesive - ADH-TLE-(CERAFIX-412PLUS)-25KG

CERAfix^® 412 C2 FT E Flex Plus tile adhesive

Name: CERAfix ® 412 C2 FT E Flex Plus tile adhesive
Brand: Würth
SKU: 5875100412

Tile adhesive Plus CERAfix 412 C2 FT Flex
ADH-TLE-(CERAFIX-412PLUS)-25KG
CERAFIX

Art.-no. 5875100412

EAN 4062856817863

All versions

Similar products

Prices for customers after login

CERAfix^® 412 C2 FT E Flex Plus tile adhesive

Art.-no. 5875100412

Prices for customers after login

Quantity

x 24 pcs

Exclusively for trade customers

Login/Register
Call customer service:

White, flexible, fast-hardening natural stone system adhesive in plastic bag in accordance with EN 12004, C2 FT

High degree of flexibility

Secure even on surfaces subject to considerable movement

Multi-use

Suitable for thin bed and medium bed mortars

Quality tested in accordance with Euro standard

Fulfils and exceeds class C2 in accordance with EN 12004

Quick to set

No long downtime once the tiles are laid

Can be walked on after just 4 hours

Prevents discolouration

Good stability and high degree of initial adhesion

Prevents tiles from slipping in vertical applications.

For adhesive bed thicknesses of up to 10 mm

Water-resistant

Can be used in wet rooms exposed to high stresses

Suitable for underfloor heating

Fast crystalline water bonding

Proof of Performance

Tested in line with EN 12004 C2 FT

Fire behaviour: A1/A1fl

Adhesive tensile strength after dry storage: ≥ 1 N/mm²

Adhesive tensile strength after water storage: ≥ 1 N/mm²

Adhesive tensile strength after warm storage: ≥ 1 N/mm²

Adhesive tensile strength after storage in alternating freezing/thawing conditions: ≥ 1 N/mm²

Early adhesive tensile strength after 6 h >/= 0.5 N/mm²

Notice

During laying, the product-specific properties of the covering materials (tendency to discolour, curling etc.) and the laying recommendations of the natural stone, tile and panel manufacturers must be observed. We recommend carrying out trial adhesions if necessary!

Thin-bed mortar that has begun to harden must not be made workable again by adding water or fresh mortar!

When laying tiles and panels on surfaces subject to high water loads, a suitable CERAfix system seal must be chosen according to the water effects!

Protect surfaces that do not require treatment against exposure to CERAfix 412 tile adhesive!

Contact between the cement-based tile mortar and the magnesite screed causes destruction of the magnesite screed by "magnesia expansion" chemical reaction. Backwards moisture load from the substrate must be prevented using appropriate means. Magnesite substrates must be mechanically roughened and primed with CERAfix 103 epoxy resin. Spread plenty of TERAfix 430 quartz sand over the fresh epoxy resin layer. After observing the specified reaction time of approx. 12-16 hours, perform laying work.

CERAfix 412 Plus is a hydraulically curing mortar that must be protected against the effects of water and frost until fully cured, which can take several days in unfavourable weather conditions.

Currently applicable regulations and the relevant standards must be observed!

For example: DIN 18157, DIN 18352, DIN 18560, DIN 18 202, DIN 1055

BEB information sheets, published by Bundesverband Estrich und Belag e. V. (Federal Association for Screeds and Coverings)

Technical information "Interface coordination for heated floor structures".

ZDB information sheets, published by Fachverband des deutschen Fliesengewerbes (German Tiling Industry Association).

Information on natural stone building technology from Deutscher Naturwerkstein-Verband e.V. (German Natural Stone Association)

Tested in line with EN 12004 C2 FT

Fire behaviour: A1/A1fl

Adhesive tensile strength after dry storage: ≥ 1 N/mm²

Adhesive tensile strength after water storage: ≥ 1 N/mm²

Adhesive tensile strength after warm storage: ≥ 1 N/mm²

Adhesive tensile strength after storage in alternating freezing/thawing conditions: ≥ 1 N/mm²

Early adhesive tensile strength after 6 h >/= 0.5 N/mm²

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Product information

Würth Catalogue

Datasheets(X)

Safety data sheet

Certificates/ Documents

Application area

For secure laying of natural stone panels with high and low water absorption. Particularly suitable for laying light-coloured, transparent materials and materials sensitive to discolouration, such as marble, granite, limestone and quartzite etc. on substrates such as concrete, autoclaved aerated concrete, suitable plaster, cement and calcium sulphate screed/hot screed, masonry or gypsum plasterboard. It is also suitable for laying ceramic coverings with high and low water absorption, such as earthenware, stoneware and stoneware tiles (water absorption ≤ 0.5 %).

Thanks to the quick, crystalline water bonding, CERAfix 412 Plus stone adhesive offers increased protection against discolouration through the constituents of the stone. It can also be used as a bonding material for lightweight panels, e.g. hard foam and tile support elements. Suitable for laying tiles on all CERAfix system seals.

Instructions

Mix tile adhesive PLUS CERAfix 412 with drinking water in a clean container, ensuring mixture is free from clumps

Mixing ratio:

5.0 - 6.0 l water: 25.0 kg tile adhesive PLUS CERAfix 412

Give the product approximately 2 minutes to mature and then stir again. Use the adhesive mortar within the processing time. Spread a flat layer of the mixed adhesive on the surface and comb through with the toothed trowel suitable for the panel size. Lay the covering materials within the adhesive drying time (test with your finger). Always clean the mixing container before mixing fresh mortar, as setting tile adhesive PLUS CERAfix 412 acts as an accelerator. Do not mix with other adhesives.

Weight of content	25 kg
Container	Sack
Chemical basis	White cement, sand, additives (polymer modified)
Standards	EN 12004
Colour	White
Min./max. processing temperature	5 to 25 °C
Processing time	1 h
Application conditions	at 20°C and 65% relative humidity
Application quantity in weight/area/conditions	2.6 kg/m² / for 6-mm toothing
Min./max. open time /conditions	15-20 min / at 20°C and 65% humidity
May be walked on after max.	4 h
May be walked on in following conditions	at 20°C and 65% relative humidity
Groutable after	4 h
Grouting condition	at 20°C and 65% relative humidity
Full load capacity/conditions	7 d / at 20°C and 65% relative humidity
Shelf life from production/conditions	12 Month / dry storage area

Required accessory:

Product

Description

Quantity

Price
/PU

Balcony sealing and uncoupling membrane CERAfix<SUP>®</SUP> 315

Balcony sealing and uncoupling membrane CERAfix® 315

WTRPROF/DECUPLMEMBR-(CERAFIX-315)-15M

CERAFIX

Art.-no. 5875100315

Sealing and isolation strip especially for balcony and terrace coverings

x 1 pcs

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).

Additive article:

Product

Description

Quantity

Price
/PU

PROFI knee pads

KNEEPAD-PROFI-EN14404

Art.-no. 089903010

For universal use for all kneeling tasks

x 1 p

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

Suitable glove:

Product

Description

Chemical protective glove, Butyl

Description:

Permeation level: 6

Gas-tight and resistant to exhaust gases produced by combustion processes

Nitrile chemical protective glove With cotton velour finish inside

Description:

Permeation level: 5

Nitrile chemical protective glove Long, heavy-duty design

Description:

Permeation level: 6

Permeation is the process by which a chemical moves through the material of a protective glove on a molecular level. The time from the initial contact between the chemical and the glove to the permeation of the material is the breakthrough time.

Measured breakthrough time

Permeation level

< 10 min

≥ 10 min

≥ 30 min

≥ 60 min

≥ 120 min

≥ 240 min

≥ 480 min

Important information:

The information given is based on experience and laboratory conditions and is designed as a guide. However, the actual suitability of a glove depends on the individual conditions of its use and must be confirmed by an appropriate test under operational conditions. Given the variety of materials and chemicals used, the possibility of incompatibility or usage problems for the wearer cannot be excluded in individual cases. We would be happy to advise you about optimum solutions.