Concrete screw with countersunk head W-BS/S - CONCSCR-(W-BS/SK)-(A2K)-TX30-5-6X40

Concrete screw with countersunk head W-BS/S - CONCSCR-(W-BS/SK)-(A2K)-TX30-5-6X40 - 1

Concrete screw with countersunk head W-BS/S - CONCSCR-(W-BS/SK)-(A2K)-TX30-5-6X40 - 2

Concrete screw with countersunk head W-BS/S

Name: Concrete screw with countersunk head W-BS/S
Brand: Würth
SKU: 5929136005

Concrete screw W-BS steel zinc plated type SK
CONCSCR-(W-BS/SK)-(A2K)-TX30-5-6X40

Art.-no. 5929136005

EAN 4046777685213

All versions

Similar products

Prices for customers after login

Concrete screw with countersunk head W-BS/S

Art.-no. 5929136005

Prices for customers after login

Quantity

x 100 pcs

Exclusively for trade customers

Login/Register
Call customer service:

Highest loads and efficient installation. For flush-mount installation of e.g. railings or handrails, zinc-plated steel

For anchorage in concrete and masonry

Extremely flexible application thanks to up to three effective anchorage depths (size 6-10)

Fastening can be adjusted up to two times after installation (size 6-10), for example in order to align railings or anchor plates (please refer to the installation instructions)

Very high loads

Very low spacing and edge distances thanks to very low expansion effect

Very fast and easy installation and immediate load-bearing capacity

Attractive, flush-mount installation possible

Proof of Performance

European Technical Assessment ETA-16/0043 for individual fixing point, option 1, cracked and uncracked concrete:

Static and quasi-static action (dia. 6-10)

Seismic action, performance category C1 (dia. 6-10) and C2 (dia. 8-10)

Fire resistance R30, R60, R90, R120

European Technical Assessment ETA-23/0196 for anchorage in masonry

Static and quasi-static action (dia. 5-10)

Fire resistance R30, R60, R90, R120 (dia. 5-6)

European Technical Assessment ETA-16/0128 for anchors in a redundant non-structural system:

Cracked and uncracked concrete, (dia. 5 and dia. 6)

Hollow-core prestressed concrete ceilings C30/37-C50/60, (dia. 6)

Fire resistance R30, R60, R90, R120

DIBt National technical approval/general type approval Z-21.1-2075 as bonded screw anchor for anchorage in concrete (dia. 10 ), type SK countersunk head

Use in combination with WIT-BS injectable mortar as WIT-BS bonded screw anchor

In reinforced and non-reinforced and cracked and uncracked concrete C20/25 to C50/60

Fire resistance rating when exposed to fire according to the standard temperature time curve in masonry (Mz, KSL, KS) and reinforced concrete, (dia. 5 and dia. 6) - expert report no 2101/173/18 - 2018

Notice

From size 8, we recommend the use of a suitable tangential impact driver for installation. The recommended maximum nominal torque must be observed. When used in masonry, the stone-specific installation data according to ETA-23/0196 must be observed.

Application area

Railings

Handrails

Adjustment - subsequent aligning possible

Create the drill hole

Clean the drill hole

Place screw

Screw in the screw

Considered installed when the head is close fitting

Screw out the screw max. 2x each by max. 10 mm. Underlay. Screw in

Considered installed when the head is close fitting. Lining max. 10 mm. The required embedment depth must be maintained as a minimum

Locate the tensioning strand

Mark the tensioning strand and locate the next one

Mark the tensioning strands. Specify the drilling range

Create the drill hole. Observe spacing

Clean the drill hole

Screw in the screw

Considered installed when the head is close fitting. Observe the embedment depth/mirror thickness

European Technical Assessment ETA-16/0043 for individual fixing point, option 1, cracked and uncracked concrete:

Static and quasi-static action (dia. 6-10)

Seismic action, performance category C1 (dia. 6-10) and C2 (dia. 8-10)

Fire resistance R30, R60, R90, R120

European Technical Assessment ETA-23/0196 for anchorage in masonry

Static and quasi-static action (dia. 5-10)

Fire resistance R30, R60, R90, R120 (dia. 5-6)

European Technical Assessment ETA-16/0128 for anchors in a redundant non-structural system:

Cracked and uncracked concrete, (dia. 5 and dia. 6)

Hollow-core prestressed concrete ceilings C30/37-C50/60, (dia. 6)

Fire resistance R30, R60, R90, R120

DIBt National technical approval/general type approval Z-21.1-2075 as bonded screw anchor for anchorage in concrete (dia. 10 ), type SK countersunk head

Use in combination with WIT-BS injectable mortar as WIT-BS bonded screw anchor

In reinforced and non-reinforced and cracked and uncracked concrete C20/25 to C50/60

Product information

Würth Catalogue

Datasheets(X)

CAD data (available after login)

Certificates/ Documents

Application area

Anchorages in concrete, individual fixing point with approval (dia. 6-10):

In normal weight concrete C20/25 to C50/60 (cracked and uncracked concrete)

Anchors in a redundant non-structural system in concrete, with approval:

In normal weight concrete C20/25 to C50/60 (cracked and uncracked concrete), (dia. 5 and dia. 6)

In hollow-core prestressed concrete ceilings C30/37-C50/60, (dia. 6)

Anchorages in masonry with approval (dia. 5-10):

In solid calcium silicate block and perforated block

In solid block masonry brick

Specifically designed for attractive, flush-mount installation

Suitable for fastening medium to heavy loads in concrete and light to medium loads in masonry:

Fastening of e.g. staircase railings and balcony balustrades, handrails, steel structures, wooden substructures, metal profiles etc. in in-place installation

Fastenings subject to seismic activity in earthquake-prone areas (only concrete)

Fastenings subject to exposure to fire

W-BS/S (galvanised steel) may only be used in dry indoor room conditions

For use in concrete < C20/25 and pressure-resistant natural stone (without approval)

Anchor size	6 mm
Anchor length (l)	40 mm
Attachment height (t fix 1)	5 mm
Thread diameter	7.5 mm
Nominal drill-bit diameter (d 0)	6 mm
Drill hole depth (h 1.1)	40 mm
Embedding depth (h nom1)	35 mm
Head diameter (d sk)	13 mm
Internal drive	TX30
Head type	Countersunk head
Material	Steel
Through-hole in the component to be connected (d f)	8 mm
Surface	Zinc plated
Type description	W-BS type SK

Anchor size [mm]			6		8		10
Performance data in concrete - fixing point according to ETA-16/0043
Permissible bending moment		M_adm [Nm]
Admissible load under seismic activity performance categories C1 and C2 see European Technical Assessment ETA-16/0043		C1	x	x		x	x	x
		C2				x		x
Admissible load when exposed to fire (R30, R60, R90, R120), see European Technical Assessment ETA-16/0043
Nominal length of thread engagement		h_nom [mm]
Admissible centric tension load¹⁾ on an individual anchor without the influence of the edge distance	Tensile zone (cracked concrete C20/25²⁾, s ≥ 3 h_ef c ≥ 1.5 h_ef)	N_perm.[kN] = C20/25²⁾
	Compressive zone (non-cracked concrete C20/25²⁾, s ≥ 3 h_ef c ≥ 1.5 h_ef)	N_perm.[kN] = C20/25²⁾
Admissible shear load¹⁾ on an individual anchor without the influence of the edge distance	Tensile zone (cracked concrete C20/25²⁾, c ≥ 10 h_ef)	V_perm. [kN] = C20/25²⁾
	Compressive zone (non-cracked concrete C20/25²⁾, c ≥ 10 h_ef)	V_perm. [kN] = C20/25²⁾

Performance data in concrete - anchors in a redundant non-structural system according to ETA-16/0128
Anchor size [mm]			5	6
Admissible load when exposed to fire (R30, R60, R90, R120), see European Technical Assessment ETA-16/0128
Nominal length of thread engagement		h_nom [mm]
Anchors in concrete in a non-structural system based on a redundant design³⁾		N_perm. [kN] ≥ C20/25
Admissible shear load¹⁾ on an individual anchor without the influence of the edge distance	Tensile zone (cracked concrete C20/25²⁾, c ≥ 10 h_ef)	V_perm. [kN] = C20/25²⁾
	Compressive zone (non-cracked concrete C20/25²⁾, c ≥ 10 h_ef)
Permissible bending moment		M_adm [Nm]

Performance data in hollow-core prestressed concrete ceilings according to ETA-16/0128
Anchor size [mm]		6
Mirror thickness [mm]		≥ 25	≥ 30	≥ 35
Anchors in a redundant non-structural system in hollow-core prestressed concrete ceilings⁵⁾	F_perm.[kN]
¹⁾ The partial safety factors of the resistances y_M regulated in the evaluation/approval and a partial safety factor of the effects of γ_F = 1.4 have been taken into account. For a combination of tensile and shear loads, for the influence of the edge distance and anchor groups please see the appropriate guidelines e.g. DIN EN 1992-4. ²⁾ The concrete has normal reinforcement. Higher values are possible for higher concrete strengths. ³⁾ The admissible loads were determined without axial influence and the influence of the edge distance. ⁴⁾ Number of attachment points ≥ 3 and at least one anchor per attachment point produces a load per attachment point of Fperm ≤ 1.4 kN or number of attachment points ≥ 4 and at least one anchor per attachment point produces a load per attachment point of Fperm ≤ 2.1 kN. The admissible loads can be increased if the design shows that the requirements governing the strength and rigidity of the component to be attached remain satisfied even after the failure of an anchor in terms of the limit state of serviceability and load-bearing capacity. ⁵⁾ The assembly data must be observed.

Installation parameters in concrete
Anchor size [mm]		5	6			8			10
Minimum member thickness	h_min [mm]	80	80			80			80
Nominal drill diameter	d₀ [mm]	5	6			8			10
Diameter of cutting edges	d_cut ≤ [mm]	5,40	6,40			8,45			10,45
Drill hole depth	h₁ ≥ [mm]	40	40	45	60	55	65	75	65	85	95
Through hole in the component being connected	d_f ≤ [mm]	7	8			12			14
Internal drive		TX25	TX30			TX40			TX50
Head diameter	d_sk [mm]	12	13			20			22
Max. rated torque of tangential impact screwdriver	T_imp,max [Nm]	110	160			300			400
Nominal length of thread engagement	h_nom [mm]	35¹⁾	35¹⁾	40	55	45	55	65	55	75	85
Minimum axis distance	s_min [mm]	35	35	40		40	50		50
Axis distance	s_cr,N [mm]	81	81	93	132	105	129	156	129	180	204
Minimum edge distance	c_min [mm]	35	35	40		40	50		50
Edge distance	c_cr,N [mm]	40,5	40,5	46,5	66	52,5	64,5	78	64,5	90	102
¹⁾For anchors in a redundant non-structural system

Installation parameters in pre-loaded hollow ceiling panels
Anchor size [mm]		6
Spacing between tensioning strands and drilled hole	a_p ≥ [mm]	50
Nominal drill diameter	d₀ [mm]	6
Through hole in the component being connected	d_f ≤ [mm]	8
Minimum axis distance	s_min [mm]	100
Minimum edge distance	c_min [mm]	100
Minimum spacing between the groups of anchors	a_min [mm]	100
Distance between cavities	l_c ≥ [mm]	100
Spacing between tensioning strands	l_p ≥ [mm]	100

Performance data of an individual anchor in solid and perforated block masonry according to ETA-23/0196
Anchor size	Nominal length of thread engagement	Admissible tensile load	Admissible shear load	Min. edge distance	Min. spacing	Distance from joints		Max. torque for manual installation	Max. torque for installation with drill/driver	Installation using tangential impact driver
Solid calcium silicate block KS NF in accordance with EN 771-2:2015-11 KS 20 - 2.0 - NF - 240 x 115 x 71 mm, stone raw density ρ ≥ 2.0 kg/dm³, stone compressive strength f_mean = 26 N/mm², minimum wall thickness h_min = 240 mm
Silka XL solid calcium silicate block KS 12DF in accordance with DIN EN 771-2:2015-11 KS- R (P) - 2.0 - 12DF - 498 x 175 x 148 mm, stone raw density ρ ≥ 1.8 kg/dm³, stone compressive strength f_mean = 14 N/mm², minimum wall thickness h_min = 175 mm
Hollow calcium silicate block KS L, 3DF in accordance with DIN EN 771-2:2015-11 SWKV KSL 12 - 1.6 - 3DF - 240 x 175 x 113 mm, stone raw density ρ ≥ 1.5 kg/dm³, stone compressive strength f_mean = 17 N/mm², minimum wall thickness h_min= 175 mm
Masonry brick Mz in accordance with DIN EN 771-1:2015-11 Mz 20 - 2.0 - NF - 240 x 115 x 75 mm, stone raw density ρ ≥ 2.1 kg/dm³, stone compressive strength f_mean = 21 N/mm², minimum wall thickness h_min = 240 mm
Lightweight concrete solid block Vbl in accordance with DIN EN 771-3:2015-11 Vbl 4 - 1.0 - 2DF - 240 x 115 x 113 mm, stone raw density ρ ≥ 1.5 kg/dm³, stone compressive strength f_mean = 4 N/mm², minimum wall thickness h_min = 240 mm
5	35	0,66	0,91	80	80	40	80	6
6	35	0,66	0,91	80	80	40	80	10	10
6	55	1,17	2,37	80	80	40	80	10		185
8	45	1,8	0,91	80	80	40	80	25		300
8	65	1,8	2,14	80	80	40	80	25		300
10	55	1,83	1,69	80	80	40	80	45		300
10	75	1,91	2,44	80	80	40	80	45		300
5	35	0,31	0,46	58	80	35	58	6	8	100
6	35	0,31	0,46	58	80	35	58	11	10	100
6	55	0,31	0,46	58	80	35	58	11		100
8	45	0,46	0,46	58	80	35	58	27		200
8	65	0,46	0,46	58	80	35	58	27		200
10	55	0,63	0,63	58	80	35	58	37		200
10	75	0,63	0,63	58	80	35	58	46		200
5	35	0,46	0,6	80	80	35	80	2	4
6	35	0,46	0,6	80	80	35	80	3	9
6	55	0,46	0,6	80	80	35	80	3	9
8	45	0,66	0,6	80	80	35	80	16	14
8	65	0,66	0,6	80	80	35	80	16	14
10	55	0,86	0,6	80	80	35	80	23		185
10	75	0,91	0,77	80	80	35	80	23		185
8	65	0,17	0,66	80	80	35	80	6	10
10	75	0,37	0,91	80	80	35	80	5	14
	h_nom	N_adm	V_adm	c_min	s_{min, \|\|} = s_{min, ⊥}	c_{j ⊥} ≥	c_{j \|\|} ≥	T_inst≤	T_inst≤	T_imp,max
[mm]	[mm]	[kN]	[kN]	[mm]	[mm]	[mm]	[mm]	[Nm]	[Nm]	[Nm]
5	35	1	0,94	80	80	35	80	6		185
6	35	0,89	0,94	80	80	35	80	11	10	185
6	55	1,4	0,94	80	80	35	80	11		185
8	45	1,17	0,94	80	80	35	80	27		300
8	65	1,23	0,94	80	80	35	80	23		300
10	55	1,06	0,94	80	80	35	80	34		300
10	75	1,29	0,94	80	80	35	80	146		300
Notes: For further details on compressive strength, spacing, edge distances and installation positions, please refer to ETA-23/0196 To determine the admissible load, the partial safety factor from ETA γ_M=2.5 was taken into account on the resistance side and a partial safety factor γ_F=1.4 on the impact side. The specified values apply to an individual anchor in masonry with f_vko: 0.15 [N/mm²] and σ_d: 0.2 [N/mm²]. For combinations of tensile and shear loads, bending torques or reduced spacing and edge distances, please see ETA-23/0196. Documentation for block removal must also be provided.

General installation parameters in masonry:
Anchor size		Diameter	5	6		8		10
Through hole in the fixture	d_f ≤	[mm]	7	8		12		14
Nominal length of thread engagement		h_nom	h_nom1	h_nom1	h_nom2	h_nom1	h_nom2	h_nom1		h_nom2
		[mm]	35	35	55	45	65	55		75
Nominal drill diameter	d0	[mm]	5	6		8		10
Diameter of cutting edges	d_cut ≤	[mm]	5,4	6,4		8,45		10,45
Drill hole depth	h₀ ≥	[mm]	55	55	75	65	85	75	95

Additional accessory:

Product

Description

Quantity

Price
/PU

Blow-out bulb for drill hole cleaning

BLWOUTBULB-F.CLN

Art.-no. 0903990003

For cleaning drill holes with a smaller diameter

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).