Joint and surface filler WLF
Joint and surface filler, WLF
FILR-(SPLICES-FACES)-LIGHTGREY-10LTR
Register now and access more than 125,000 products
Light filler
- Excellent filling power
- Highly-viscous
- Low volumetric weight
- Stable surface
Ready for use
- Easy to apply
- No mixing tools required
- Powder and water do not spill
- Consistently high level of quality
Cracks do not form as shrinkage is low
Extremely supple and easy to sand
Environmentally friendly
- Work implements can be cleaned with water
- Solvent-free
Wear a fine-dust mask when sanding.
Store WLF joint and surface filler in a cool, but frost-free place. Do not expose to direct sunlight.
The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.
Datasheets(X)
Filling and grouting plasterboards in dry interior finishing and for walls and ceilings, and for indoor plastering with concrete, aerated concrete and sand-lime brick substrates. Also ideal for surface filling.
As it is not resistant to abrasion, we advise against using as a final coating or in damp rooms.
It is recommended to use a paper reinforcement strip.
WLF joint and surface filler is applied with a steel spatula at a minimum temperature of +5°C. Then lay the fibreglass reinforcement strips (art. no. 0992500001) in the fresh filler and subsequently spread over it. The surface must be clean, load-bearing and dry. Maximum coat thickness: approx. 5 mm. Note the risk of discolouration through e.g. rust, nicotine, formwork oil or other similar substances. An insulating primer layer must be applied here. Wear a fine-dust mask when sanding. Thoroughly remove all dust from the sanded surface before applying wallpaper or paint.
Material consumption:
- Joint filling: approx. 1 litre for 4-6 running metres at 2-3x filling
- Surface filling: approx. 1 litre/m2 at 1 mm layer thickness
Density | 1.15 kg/l |
Adhesive agent | Latex |
Min./max. processing temperature | 5 to 35 °C |
Solvent | Water |
Grain size | 0.15 mm |
Colour | Light grey (bright grey) |
Min./max. drying time | 2-3 h |
Filler | Perlite and white dolomite marble |
Min. proportion of solids | 60 % |
pH value | 9 |
Contents | 10 l |
Container | Bucket |
Shelf life from production | 12 Month |
Conditions for drying time | at 20°C and 50% relative humidity per 1-mm layer thickness |
Flammability | None (does not spread or feed fire) |
Solvent-free | Yes |
Min. adhesive strength | 1.3 N/mm² |
Additional articles | Sanding mesh P60 to P240, art. no. 0585600…; sandpaper, art. prefix no. 0584… |
Select RAL-colour code
!! NOTE: On-screen visualisation of the colour differs from real colour shade!!
Last viewed
ASSY® 4 A2 CS fittings screw A2 stainless steel plain full thread countersunk head
PRO trough panel set
Hexagon Socket Head Cap Screw
Hexagonal bolt with shank SB FITTINGS DIN EN 15048-1 ISO 4014, steel 8.8U, hot-dip galvanised, with nut ISO 4032
Holder For adhesive weights on 5 kg rolls
Protective glove, winter
ASSY® 4 A2 RCS wood façade screw A2 stainless steel plain partial thread raised countersunk head
Nail screw Primarily suitable for softwood
Lens For contour lights
ELMO® connection terminal, screwless, compact For single-wire rigid copper conductors