Joist bracket

Name: Joist bracket
Brand: Würth
SKU: 068135090

Beam bearer
BMBEAR-H90MM

Art.-no. 068135090

EAN 4024835148375

All versions

Prices for customers after login

Joist bracket

Art.-no. 068135090

Prices for customers after login

Quantity

x 25 pcs

Exclusively for trade customers

Login/Register
Call customer service:

Specification

Joist brackets are ideal for concealed load-bearing wood/wood connections of e.g. secondary beams to main beams or posts. Connections in visible areas can also be sloping.

Easy on-site installation thanks to mounting slot in joist bracket blade

Sheet metal hot-dip galvanised on both sides (S250GD +Z275 (approx. 20 µm)), thickness 3.0 mm in line with EN 10327:2004

Application in utilisation classes 1 and 2 in line with EN 1995:2013

Proof of Performance

ETA-09/0105

Notice

The secondary beam can be mounted on the joist bracket attached to the main beam after the first dowel pin has been driven in to the uppermost hole in the secondary beam. To do this, the secondary beam with the uppermost dowel pin mounted in the slot area is hooked into the blade area of the joist bracket from above.

The secondary beam should be approx. 40 mm taller than the joist bracket. If the bracket is 90 mm in height, a secondary beam 100 mm in height can be used.

The diameter of the dowel pin may only be max. 0.5 mm (d = 8 mm) or 1.0 mm (d = 12 mm) smaller than the diameter of the hole.

Available work documents:

Load tables and detailed processing instructions can be found on the service page www.wuerth.de/holzverbinder.

Application area

ETA-09/0105

Subject to technical changes!

Application

Application area

Load-bearing connections of timber joists to timber main beams or posts in visible areas

Instructions

Suitable fasteners:

Ribbed nail in line with EN 14592: 4.0x40 mm

Dowel pin in line with EN 14592, d = 8, 12 mm

Technical information


Width x height x depth	46 x 90 x 106 mm
Min. joist hanger height	100 mm
Hole diameter in subcarrier nJ/main carrier nH	8.5 / 5 mm
Number of holes in subcarrier nJ/main carrier nH	3 / 8 PCS
Weight	470 g
Approval	ETA-09/0105
Thickness	3 mm
Material	Steel
Material designation	DX51D
Material standard	DIN EN 10327:2004
Surface	Hot dip galvanized

Characteristic load-bearing capacities in kN with Würth joist bracket according to ETA-09/0105, secondary beam width 60 mm
Characteristic load-bearing capacities Würth joist bracket, solid wood C24 according to DIN 380 (Ƥ_k = 350 kg/m³), secondary beam width 60 mm
Art. no.	Joist bracket height in mm	Complete nailing with Würth comb/anchor nails				Minimum width/height in mm
		F_z,down,Rk		F_z,up,Rk
		4 x 40mm	4 x 60mm	4 x 40mm	4 x 60mm
0681 350 90	90	3,57	5,79	4,63	7,4	60/130 (100)
0681 350 120	120	11,02	11,02	7,06	7,06	60/160
0681 350 160	160	17,76	17,76	13,48	13,48	60/200
0681 350 200	200	25,67	25,67	20,3	21,39	60/240
0681 350 240	240	33,65	34,44	27,36	30,38	60/280
Characteristic load-bearing capacities Würth joist bracket, glued laminated timber GL 24h according to DIN EN 14080 (Ƥ_k = 385 kg/m³), secondary beam width 60 mm
Art. no.	Joist bracket height in mm	Complete nailing with Würth comb/anchor nails				Minimum width/height in mm
		F_z,down,Rk		F_z,up,Rk
		4 x 40mm	4 x 60mm	4 x 40mm	4 x 60mm
0681 350 90	90	4,17	6,70	5,39	8,50	60/130 (100)
0681 350 120	120	12,12	12,12	7,77	7,77	60/160
0681 350 160	160	19,53	19,53	14,83	14,83	60/200
0681 350 200	200	28,24	28,24	22,96	23,53	60/240
0681 350 240	240	36,94	37,89	30,71	33,42	60/280
Factor table for design value:
NKL	Continuously	Long	Medium	Short	Short/very short	Very short
1 and 2	0,462	0,538	0,615	0,692	0,769	0,846
Notes: The measurement tables can only be used if all nails and rod anchors are inserted into the intended holes. The secondary beam should be about 40 mm greater in height than the joist bracket. The load-bearing capacities of the respective fasteners are determined in accordance with DIN EN 1995-1-1/NA. The force F_z,down and Fz,up_Z,up act in the centre of the secondary beam. The main support must be secured to prevent torsion. The gap between the main support and the secondary beam must not exceed 8 mm. The transverse tensile capacity of the main support must be investigated separately. If necessary, a transverse tension reinforcement with ASSY plus FT screws must be used. For one-sided connections on the main support, the offset moment must be taken into account. The regulations of ETA-09/0105 must be applied. M_ex = F x (width HT/2 + 40mm) These are guides for planning purposes. The values must be calculated for each project by authorised persons.

Characteristic load-bearing capacities in kN with Würth joist bracket according to ETA-09/0105, secondary beam width 100 mm
Characteristic load-bearing capacities Würth joist bracket, solid wood C24 according to DIN 380 (Ƥ_k = 350 kg/m³), secondary beam width 100 mm
Art. no.	Joist bracket height in mm	Complete nailing with Würth comb/anchor nails				Minimum width/height in mm
		Fz,down,Rk		Fz,up,Rk
		4 x 40mm	4 x 60mm	4 x 40mm	4 x 60mm
0681 350 90	90	3,57	5,79	4,63	7,4	100/130 (100)
0681 350 120	120	12,03	17,2	7,7	11,23	100/160
0681 350 160	160	19,23	26,46	13,63	20,42	100/200
0681 350 200	200	26,47	35,61	20,3	29,48	100/240
0681 350 240	240	33,65	44,65	27,36	38,76	100/280
Characteristic load-bearing capacities Würth joist bracket, glued laminated timber GL 24h according to DIN EN 14080 (Ƥ_k = 385 kg/m³), secondary beam width 100 mm
Art. no.	Joist bracket height in mm	Complete nailing with Würth comb/anchor nails				Minimum width/height in mm
		Fz,down,Rk		Fz,up,Rk
		4 x 40mm	4 x 60mm	4 x 40mm	4 x 60mm
0681 350 90	90	4,17	6,70	5,39	8,50	100/130 (100)
0681 350 120	120	13,52	18,38	8,88	11,78	100/160
0681 350 160	160	21,37	28,65	15,57	22,49	100/200
0681 350 200	200	29,20	38,30	22,96	32,51	100/240
0681 350 240	240	36,94	47,82	30,71	42,38	100/280
Factor table for design value:
NKL	Continuously	Long	Medium	Short	Short/very short	Very short
1 and 2	0,462	0,538	0,615	0,692	0,769	0,846
Notes: The measurement tables can only be used if all nails and rod anchors are inserted into the intended holes. The secondary beam should be about 40 mm greater in height than the joist bracket. The load-bearing capacities of the respective fasteners are determined in accordance with DIN EN 1995-1-1/NA. The force F_z,down and F_z,up act in the centre of the secondary beam. The main support must be secured to prevent torsion. The gap between the main support and the secondary beam must not exceed 8 mm. The transverse tensile capacity of the main support must be investigated separately. If necessary, a transverse tension reinforcement with ASSY plus FT screws must be used. For one-sided connections on the main support, the offset moment must be taken into account. The regulations of ETA-09/0105 must be applied. M_ex = F x (width HT/2 + 40mm) These are guides for planning purposes. The values must be calculated for each project by authorised persons.

Characteristic load-bearing capacities in kN with Würth joist bracket according to ETA-09/0105, secondary beam width 80 mm
Characteristic load-bearing capacities Würth joist bracket, solid wood C24 according to DIN 380 (Ƥ_k = 350 kg/m³), secondary beam width 80 mm
Art. no.	Joist bracket height in mm	Complete nailing with Würth comb/anchor nails				Minimum width/height in mm
		F_z,down,Rk		F_z,up,Rk
		4 x 40mm	4 x 60mm	4 x 40mm	4 x 60mm
0681 350 90	90	3,57	5,79	4,63	7,4	80/130 (100)
0681 350 120	120	12,03	15,1	7,7	9,67	80/160
0681 350 160	160	19,23	24,33	13,63	18,47	80/200
0681 350 200	200	26,47	35,18	20,3	29,32	80/240
0681 350 240	240	33,65	44,65	27,36	38,76	80/280
Characteristic load-bearing capacities Würth joist bracket, glued laminated timber GL 24h according to DIN EN 14080 (Ƥ_k = 385 kg/m³), secondary beam width 80 mm
Art. no.	Joist bracket height in mm	Complete nailing with Würth comb/anchor nails				Minimum width/height in mm
		F_z,down,Rk		F_z,up,Rk
		4 x 40mm	4 x 60mm	4 x 40mm	4 x 60mm
0681 350 90	90	4,17	6,70	5,39	8,50	80/130 (100)
0681 350 120	120	13,54	16,61	8,88	10,64	80/160
0681 350 160	160	21,37	26,77	15,57	20,32	80/200
0681 350 200	200	29,20	38,30	22,96	32,25	80/240
0681 350 240	240	36,94	47,82	30,71	42,38	80/280
Factor table for design value:
NKL	Continuously	Long	Medium	Short	Short/very short	Very short
1 and 2	0,462	0,538	0,615	0,692	0,769	0,846
Notes: The measurement tables can only be used if all nails and rod anchors are inserted into the intended holes. The secondary beam should be about 40 mm greater in height than the joist bracket. The load-bearing capacities of the respective fasteners are determined in accordance with DIN EN 1995-1-1/NA. The force F_z,down and F_z,up act in the centre of the secondary beam. The main support must be secured to prevent torsion. The gap between the main support and the secondary beam must not exceed 8 mm. The transverse tensile capacity of the main support must be investigated separately. If necessary, a transverse tension reinforcement with ASSY plus FT screws must be used. For one-sided connections on the main support, the offset moment must be taken into account. The regulations of ETA-09/0105 must be applied. M_ex= F x (width HT/2 + 40mm) These are guides for planning purposes. The values must be calculated for each project by authorised persons.

Documents

Product information

Datasheets (0)

Certificates/ Documents (0)

Accessory

Required accessory:

Product

Description

Quantity

Price
/PU

Dowel pins

RODPLG-(A2K)-8X65MM

Art.-no. 0681008065

Fastener between steel parts, such as post support brackets with strut and wood ties

x 100 pcs

Dowel pins

RODPLG-(A2K)-8X90MM

Art.-no. 0681008090

Fastener between steel parts, such as post support brackets with strut and wood ties

x 100 pcs

Dowel pins

RODPLG-(A2K)-8X115MM

Art.-no. 0681008115

Fastener between steel parts, such as post support brackets with strut and wood ties

x 100 pcs

Comb nail / anchor nail

RIDGNL-(A3K)-4X40MM

Art.-no. 0681940040

Galvanised steel, blue coated (A2K)

x 3000 pcs

Comb nail / anchor nail

RIDGNL-(A3K)-4X50MM

Art.-no. 0681940050

Galvanised steel, blue coated (A2K)

Comb nail / anchor nail

RIDGNL-(A3K)-4X60MM

Art.-no. 0681940060

Galvanised steel, blue coated (A2K)

Comb nail / anchor nail

RIDGNL-(A3K)-4X75MM

Art.-no. 0681940075

Galvanised steel, blue coated (A2K)

x 250 pcs

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with v

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).