Repair cement - ASMBYMORT-QCK-FIXINGCEMENT-5KG

Repair cement

Name: Repair cement
Brand: Würth
SKU: 0890350

Quick-setting installation cement fixing cement
ASMBYMORT-QCK-FIXINGCEMENT-5KG

Art.-no. 0890350

EAN 4011231823012

All versions

Similar products

Prices for customers after login

Repair cement

Art.-no. 0890350

Prices for customers after login

Quantity

x 1 pcs

Exclusively for trade customers

Login/Register
Call customer service:

Quick-setting assembly cement

Does not contain chloride, and is therefore not corrosive

For universal use indoors and outdoors

Quick installation with earlier load-bearing capacity

Solidification finished after approx. 3 minutes

Can be reworked after an hour (coating, plasters)

Quickly reaches a high level of tensile bending and compressive strength

Notice

Protect from frost!

All clean and load-bearing, solid, non-slip, mineral and permitted substrates are classed as suitable substrates. (Gypsum substrates must be primed beforehand with CERAfix 101). Do not mix with other substances (such as gypsum). Do not over-water. Do not use in a pourable state. The processing time refers to an air and object temperature of +20°C.

Application area

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Product information

Würth Catalogue

Datasheets(X)

Safety data sheet

Certificates/ Documents

Application area

For temporary and secondary fastenings. For installing and anchoring doors and window frames, switchboards, flush-mounted boxes as well as for sealing seepage points in masonry, concrete and cement pipes. For anchoring anchor screws, dowels, masonry hooks, pipe clamps and much more.

Instructions

Floor drains should be provided with thin bed flanges that have a minimum all-round width of 5 cm and should be made of a material suitable for bonding, e.g. stainless steel, gunmetal or PVC-U.

Chemical basis	Mix of Portland/alumina cement
Colour	Grey
Density	1.45 g/cm³
Density conditions	at 20°C
Mixing ratio	0.3 l water for 1 kg
Application conditions	at 20°C
Min. working life	1 min
Max. processing time	3 min
Further processing conditions	at 20°C
Min. curing time	5 min
Min. processing temperature	5 °C
Max. processing temperature	30 °C
Building material class	A1 - Non-flammable
Building material class conditions	in accordance with DIN EN 13501-1
Max. flexural strength	3.8 N/mm²
Conditions for flexural strength	in accordance with DIN EN 196-1 after seven days
Max. compressive strength	22.5 N/mm²
Compressive strength conditions	after 7 days, DIN EN 196-1
Weight of content	5 kg
Container	Bucket
Shelf life from production	12 Month
Conditions to maintain shelf life from production	cool and dry storage area

Flexural strength	approx. 2.8 N/mm²	After 1 hour and according to DIN EN 196-1
	approx. 3.5 N/mm²	After 2 hour and according to DIN EN 196-1
	approx. 3.6 N/mm²	After 1 day and according to DIN EN 196-1
	approx. 3.8 N/mm²	After 7 days and according to DIN EN 196-1
Compressive strength	approx. 7.6 N/mm²	After 1 hour and according to DIN EN 196-1
	approx. 11.5 N/mm²	After 2 hour and according to DIN EN 196-1
	approx. 13.1 N/mm²	After 1 day and according to DIN EN 196-1
	approx. 22.5 N/mm²	After 7 days and according to DIN EN 196-1

Additive article:

Product

Description

Quantity

Price
/PU

Bricklayers trowel, forged Suitable even for the most demanding tasks, since handle and blade are forged from one piece

BRCKLRTRWL-(S-NECK)-FORGED-B160MM

Art.-no. 0695943100

Suitable even for the most demanding tasks, since handle and blade are forged from one piece.

x 1 pcs

Bricklayers trowel, forged Suitable even for the most demanding tasks, since handle and blade are forged from one piece

BRCKLRTRWL-(S-NECK)-FORGED-B180MM

Art.-no. 0695943101

Suitable even for the most demanding tasks, since handle and blade are forged from one piece.

x 1 pcs

Bricklayers trowel, welded

BRCKLRTRWL-(S-NECK)-WELDED-B180MM

Art.-no. 0695943110

High-quality brick trowel with welded blade

x 1 pcs

Bricklayers trowel, welded

BRCKLRTRWL-(G-NECK)-WELDED-180MM

Art.-no. 0695943111

High-quality brick trowel with welded blade

x 1 pcs

Polycarbonate safety goggles

SAFEGOGL-POLYCARBONATE

Art.-no. 0899102230

Can be worn over all prescription glasses

x 1 pcs

Yellow nitrile glove

PROTGLOV-NTR-YELLOW-SZ8

Art.-no. 089941008

Universal, lightweight assembly glove with nitrile coating

x 12 pcs

Yellow nitrile glove

PROTGLOV-NTR-YELLOW-SZ9

Art.-no. 089941009

Universal, lightweight assembly glove with nitrile coating

x 12 pcs

Yellow nitrile glove

PROTGLOV-NTR-YELLOW-SZ10

Art.-no. 089941010

Universal, lightweight assembly glove with nitrile coating

x 12 pcs

Economy nitrile glove, yellow

PROTGLOV-NTR-ECONOMY-YELLOW-SZ9

Art.-no. 0899410109

Lightweight assembly glove with nitrile coating

Economy nitrile glove, yellow

PROTGLOV-NTR-ECONOMY-YELLOW-SZ10

Art.-no. 0899410110

Lightweight assembly glove with nitrile coating

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).

Suitable glove:

Product

Description

Nitrile chemical protective glove With cotton velour finish inside

Description:

Permeation level: 6

Nitrile chemical protective glove Long, heavy-duty design

Description:

Permeation level: 6

Permeation is the process by which a chemical moves through the material of a protective glove on a molecular level. The time from the initial contact between the chemical and the glove to the permeation of the material is the breakthrough time.

Measured breakthrough time

Permeation level

< 10 min

≥ 10 min

≥ 30 min

≥ 60 min

≥ 120 min

≥ 240 min

≥ 480 min

Important information:

The information given is based on experience and laboratory conditions and is designed as a guide. However, the actual suitability of a glove depends on the individual conditions of its use and must be confirmed by an appropriate test under operational conditions. Given the variety of materials and chemicals used, the possibility of incompatibility or usage problems for the wearer cannot be excluded in individual cases. We would be happy to advise you about optimum solutions.