Repair layer
Protective coating Waterproofing Compound
REPCOMPD-PFLEX-GREY-750ML
Register now and access more than 125,000 products
Silicone-based
- Retains long-term elasticity even in extreme weather conditions and does not become brittle
- UV and weathering resistant
- Solvent-free
Crack-bridging
A layer thickness of 2–3 mm is achieved with just one application.
Easy to process
Can be applied with a brush, short-pile roller or trowel.
Easy to clean
Your hands, clothing, tools and dirty marginal areas can be cleaned with water.
Compatible with bitumen
Not suitable for area continuously exposed to water (e.g. fountains, cisterns).
The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.
Datasheets(X)
The repair layer is suitable for smaller and larger surfaces for indoor and outdoor use, and protects against weathering, decay and damage caused by humidity. The coating is ideal for repairing eaves gutters, holes and tears in roof sheeting, roofing tiles, in walls, in water channels, roof windows and window openings, balconies and terraces.
The surface must be load-bearing, clean, free from dust and grease as well as being dry or slightly damp (max. 5% residual moisture). Remove moss, algae and lichen as well as loose parts and primer mechanically. The repair layer is ready for application. Once the surface has been prepared, apply an even, undiluted and thick layer directly with a
brush, roller, swab or a short-haired velour roller within the processing temperature. A wet application layer of at least 3–5 mm is required on moving surfaces. A wet application thickness of 2 mm is sufficient on roofs with a roof slope ≥5°. Unhardened material can be removed with a damp sponge. Hardened material can only be removed mechanically. Clean your hands and equipment with water immediately after use. Dispose of hardened product remains in the household rubbish and/or in industrial waste similar to household rubbish; dispose of unhardened products in special waste disposal or communal waste disposal points. Recycle completely emptied containers.
Chemical basis | Neutral silicones, water-based |
Colour | Grey |
Density | 1.3 g/cm³ |
pH value | 10.5 |
Smell/fragrance | Faint odour |
Viscosity/consistency | Viscous, non-dripping |
Min. skin-formation time | 30 min |
Conditions for skin-formation time | at 23°C and 50% relative humidity |
Full curing speed | 2 mm/d |
Fully hardening/curing conditions | 23°C and 50% relative humidity |
Min. processing temperature | 5 °C |
Max. processing temperature | 40 °C |
Min. temperature resistance | -50 °C |
Max. temperature resistance | 150 °C |
Resistance against | Weather |
Ultraviolet resistance | Yes |
Min./max. application quantity in volume/area | 1-3 l/m² |
Contents | 0.75 l |
Container | Bucket |
Shelf life from production | 18 Month |
Conditions to maintain shelf life from production | cool and frost-free storage |
Last viewed
Twist drill bit, metal Ruko DIN 338 HSS-G plain 118° inch
Vertical clamp Pro With open support arm
Hexagon Socket Head Cap Screw ISO 4762/DIN 912, A2-70 stainless steel
Safety goggles uvex i-3 s 9190
Hexagon Socket Head Cap Screw ISO 4762/DIN 912, steel 10.9, plain
Hexagon Socket Head Cap Screw ISO 4762/DIN 912, steel 10.9, zinc-plated, blue passivated (A2K)
Ear defenders
Installation box, shut-off valve, masonry
Hexagonal bolt with thread up to the head DIN 933, A4 stainless steel, plain
Threaded rod