Welcome to Würth Aerospace Solutions For trade customers only

Retouching paint pens, assortment

Retouching paint pen assortment
RETCHPEN-SORT-LACQUER-10PCS

Art.-no. 09648901
EAN 4011231883771

Prices for customers after login
Retouching paint pens, assortment

Art.-no. 09648901

Prices for customers after login
Quantity
PU
x 1 pcs

Exclusively for trade customers

Register now and access more than 125,000 products

For recolouring and covering edges and scratches as well as for pre-colouring damaged areas. A sprung pen tip provides an even flow of paint and therefore optimum results.

Easy and quick to apply


  • No brush and paint pot required

  • Ready to use immediately and quick-drying


Large selection of colours for a wide range of different wood colour tones.



Good adhesion


  • Adheres to a range of surfaces, making it suitable for universal use

  • Resistant to smearing and scratch-resistant


Suitable for indoor and outdoor use

Notice

The retouching pens are not refillable.

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Product information

Datasheets(X)

Safety data sheet

Certificates/ Documents

 | 

 | 

Application area

For recolouring and covering edges, scratches, chafe marks, minor touch-up defects and mitre grooves as well as correcting wood colours. Optimum paint quality for a continuous flow of paint. For both indoor and outdoor use.

Instructions

Shake the pin for approx. 30 seconds before use. The stirring balls must be clearly audible. Remove the pen lid and hold the pen with the tip pointing upwards. The pen is audibly vented by briefly pressing on "P". Then point the tip downwards to activate the pen. The tip is slowly filled with paint by carefully pressing on "P". Apply light pressure to use the pen at a flat angle (approx. 45°). The valve opens and the paint flows evenly and continues to do so. During application, avoid pressing on "P", as this can lead to an uncontrolled flow of paint. Thanks to the new shape of the tip, it is also easy to work hard-to-reach areas (corners, narrow areas) with precision.

Density

0.94 g/cm³

Density conditions

at 20°C

Min. grip strength

2 min

Max. grip strength

5 min

Grip strength conditions

depending on room temperature and layer thickness

Min. dust-drying time

1 min

Max. dust-drying time

2 min

Conditions for dust-drying time

depending on room temperature and layer thickness

Ignition temperature

350 °C

Min. flashing point

19 °C

Number of pieces in assortment/set

10 PCS

Light-fastness

Good

Water-soluble

No

Shelf life from production

24 Month

Retouching paint pens, assortment including:
1 x
Paint retouching pen

RETCHPEN-LACQUER-SIGNALWHITE-11G

Description:
Colour: Signal white
For recolouring and covering edges and scratches as well as for pre-colouring damaged areas. A sprung pen tip provides an even flow of paint and therefore optimum results.
Quantity: 1 x
1 x
Paint retouching pen

RETCHPEN-LACQUER-MAPLE-NATURE-11G

Description:
Colour: Maple
For recolouring and covering edges and scratches as well as for pre-colouring damaged areas. A sprung pen tip provides an even flow of paint and therefore optimum results.
Quantity: 1 x
1 x
Paint retouching pen

RETCHPEN-LACQUER-PINE-11G

Description:
Colour: Pine
For recolouring and covering edges and scratches as well as for pre-colouring damaged areas. A sprung pen tip provides an even flow of paint and therefore optimum results.
Quantity: 1 x
1 x
Paint retouching pen

RETCHPEN-LACQUER-BEECH-LIGHT-11G

Description:
Colour: Beech, light
For recolouring and covering edges and scratches as well as for pre-colouring damaged areas. A sprung pen tip provides an even flow of paint and therefore optimum results.
Quantity: 1 x
1 x
Paint retouching pen

RETCHPEN-LACQUER-ALDER-DARK-HONEY-11G

Description:
Colour: Alder
For recolouring and covering edges and scratches as well as for pre-colouring damaged areas. A sprung pen tip provides an even flow of paint and therefore optimum results.
Quantity: 1 x
1 x
Paint retouching pen

RETCHPEN-LACQUER-CHERRYTREE-MIDDLE-11G

Description:
Colour: Cherry tree
For recolouring and covering edges and scratches as well as for pre-colouring damaged areas. A sprung pen tip provides an even flow of paint and therefore optimum results.
Quantity: 1 x
1 x
Paint retouching pen

RETCHPEN-LACQUER-PEARTREE-MIDDLE-11G

Description:
Colour: Pear
For recolouring and covering edges and scratches as well as for pre-colouring damaged areas. A sprung pen tip provides an even flow of paint and therefore optimum results.
Quantity: 1 x
1 x
Paint retouching pen

RETCHPEN-LACQUER-RUSTIC-OAK-11G

Description:
Colour: Oak, rustic
For recolouring and covering edges and scratches as well as for pre-colouring damaged areas. A sprung pen tip provides an even flow of paint and therefore optimum results.
Quantity: 1 x
1 x
Paint retouching pen

RETCHPEN-LACQUER-WALNUT-ANTIQUE-11G

Description:
Colour: Walnut
For recolouring and covering edges and scratches as well as for pre-colouring damaged areas. A sprung pen tip provides an even flow of paint and therefore optimum results.
Quantity: 1 x
1 x
Paint retouching pen

RETCHPEN-LACQUER-DEEPBLACK-11G

Description:
Jet black, similar to RAL 9005
For recolouring and covering edges and scratches as well as for pre-colouring damaged areas. A sprung pen tip provides an even flow of paint and therefore optimum results.
Quantity: 1 x
The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.
The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076
Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units
The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.
In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).
Suitable glove:
 
Product
Description
Chemical protective glove made from natural latex and chloroprene
Chemical protective glove made from natural latex and chloroprene
Description:
Permeation level: 1
Cotton flocking on the inside
Permeation is the process by which a chemical moves through the material of a protective glove on a molecular level. The time from the initial contact between the chemical and the glove to the permeation of the material is the breakthrough time.
Measured breakthrough time
Permeation level
< 10 min
0
≥ 10 min
1
≥ 30 min
2
≥ 60 min
3
≥ 120 min
4
≥ 240 min
5
≥ 480 min
6

Important information:

The information given is based on experience and laboratory conditions and is designed as a guide. However, the actual suitability of a glove depends on the individual conditions of its use and must be confirmed by an appropriate test under operational conditions. Given the variety of materials and chemicals used, the possibility of incompatibility or usage problems for the wearer cannot be excluded in individual cases. We would be happy to advise you about optimum solutions.

Art.-no.
Cust. Mat. No.

Hazardous Material

Product information

Datasheets()

Datasheets ()

CAD data  | 

Certificates/ Documents

 | 

 | 

Technical information