TEGAfix® 100 bedding and drainage mortar
Bedding and drain mortar
MORT-(TEGAFIX-100)BEDDING-DRAINAGE-25-KG
TEGAFIX
Register now and access more than 125,000 products
- One-component draining mineral bedding mortar
- Draining in accordance with DIN 18130-1
- Highly resistant to frost and de-icing salt
- Low shrinkage and residual stress
- Shelf life of 12 months when stored in a cool, dry place protected from the weather
- Technical data applies to +20°C and 50 % relative humidity; lower temperatures increase the specified values, while higher temperatures decrease the specified values
- Material that is already beginning to set must not be diluted further with water
The usage instructions are recommendations based on the tests we have conducted and on our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting with deliberate intent. We guarantee the consistent quality of our products. We reserve the right to make technical changes and further develop products. Please observe the technical data sheet!
Datasheets(X)
- For N1-N3 in accordance with ZTV Wegebau (Supplementary Technical Conditions of Contract for the Construction of Paths and Public Spaces outside Areas of Road Traffic)
- In accordance with FGSV leaflet for areas with heavy traffic, in accordance with DIN EN 124/1229 up to Class D 400
Always mix the entire container of TEGAfix® 100 regardless of the application, mixing the whole bag with approx. 3 l of water to form an earth-moist mortar. Do not add any other additives or anti-freeze to the mortar.
Once mixed, the mortar must be used within two hours.
To improve the adhesion, we recommend applying TEGAfix® 200 bonding and contact slurry to the back of the stones.
The use of TEGAfix® 200 bonding and contact slurry is mandatory for paving.
Weight of content | 25 kg |
Chemical basis | Cement - DIN EN 197, Selected Aggregates - DIN EN 13139, additives and aggregates |
Colour | Grey |
Max. processing time | 90 min |
Hardening time | 25 min |
Min./max. processing temperature | 5 to 30 °C |
Processing time | 90 min |
Application conditions | at min. 5°C and max. 80% relative humidity |
Application quantity in weight/area/conditions | 16 kg/m² / for 10-mm layer thickness |
Can be covered after max. | 3 d |
May be walked on after max. | 24 h |
May be walked on in following conditions | at 20°C and 50% relative humidity |
Groutable after | 3 d |
Shelf life from production/conditions | 12 Month / cool, dry and frost-free storage area |
| Water requirements per 25 kg | Approx. 3 l |
| Consistency | Earth-moist |
| Coverage | 2 kg/m² and mm layer thickness |
| Yield | 0.5 l/kg |
| Processing time | Approx. 2 hrs |
| Application temperature | +5°C to +30°C |
| Largest grain size | 4 mm |
| Layer thickness | 50 - 100 mm |
| Compressive strength | ≥ 30 N/mm² |
| Rain seepage | Approx. 2600 l/(s*ha) |
| Adhesive pull strength to substrate (with TEGAfix 200) | Approx. 2 N/mm² |
Select RAL-colour code
!! NOTE: On-screen visualisation of the colour differs from real colour shade!!
Last viewed
Hexagonal nut with flange and clamping piece (all-metal) according to MBN standard
Protective glove accessories
Door handle A 802 on oval escutcheon
Full-vision goggles FS503
Work overall
Stretch X winter trousers
Accessories, hammers Halder hammer insert Series 3209
GEFU® thread-rolling screw With Taptite 2000® thread, flat head and hexalobular drive
PRIPRESS® composite pipe
Threaded rod, fine thread DIN 976-1, steel 8.8, plain, shape A