Vapour retarder WÜTOP^®DB 2

Name: Vapour retarder WÜTOP ® DB 2
Brand: Würth
SKU: 0681000144

WÜTOP DB 2 vapour retarder
VAPRETRDR-DB02-L50M-W3,0M-150SM

Art.-no. 0681000144

EAN 4050642853355

All versions

Specification

Vapour-permeable, moisture-regulating, airtight and easy-to-install vapour retarder for interior renovations and attic conversions. To be used in conjunction with vapour-permeable underlay membranes and roof protection films

Embedded mesh for durability and tear resistance

Prevents heat loss caused by unnecessary airflow

Prevents moisture penetration of internal heat insulation and, therefore, the impairment of the insulating effect

Wütop DB 2 in combination with water vapour-permeable non-breathable membrane from the Wütop series provides year-round breathability for insulation and frame structure, creating a healthy indoor climate

Our products featuring the EMICODE label are low-emission/low in harmful substances. The EMICODE classification system awards labels to construction products that comply with the very stringent health and environmental requirements of recognised institutes.

DIN EN 13984

EMICODE EC1plus: Very low emissions: The EMICODE classification system distinguishes the environmental and health compatibility of construction products. The lowest-emission products bear the EC1plus mark.

Application

Instructions

Installation instructions for between-rafter insulation

Fix Wütop DB 2 to the warm side of the heat insulation using a stapler (hammer tacker or hand-held stapler) and secure with battens

The smooth side always faces toward the installer

Vertical overlaps must always lie on a rafter

Ensure sufficient overlap: Horizontal overlap: at least 10 cm (overlap strip), vertical overlap: approx. 20 cm

All overlaps and stapled points must be given an airtight seal using suitable adhesive tape (Eurasol)

For airtight attachment to masonry, the membrane is bonded using Wütop film adhesive and secured with a clamping batten, if necessary

Take care not to damage the membrane during installation

Before the interior cladding is attached (gypsum plasterboard, wood panelling etc.), check again that the vapour retarder has been correctly installed and correct if necessary

Installation instructions for over-rafter insulation

Wütop DB 2 is ideal for use as a vapour retarder for over-rafter insulation

Installation: Same procedure as for between-rafter insulation

Please keep in mind: May be exposed to weather for max. 6 weeks

Installation instructions for renovation of old buildings

Sharp objects (e. g. nails) that protrude from the interior cladding into the rafter area must be removed to avoid damaging the vapour retarder

Wütop DB 2 is laid over the rafters from the outside with the fleece facing the room interior. Install with the smooth side facing outwards

All overlaps and openings must be given an airtight seal using suitable adhesive tape (Eurasol)

Recommendation: Secure Wütop DB 2 to the rafters using clamping battens

Bond joints at the eaves (eave beams or masonry) using Wütop film adhesive. Additional mechanical fixing with clamping battens is recommended

Wütop DB 2 vapour retarder must not be used to renovate interiors in which the humidity is continually over 60%

According to DIN 4108 part 3, structures that do not conform to standard construction methods must be verified with a calculation (dew point calculation). Therefore, the use of Wütop DB 2 for renovation work must be agreed upon beforehand by Würth Application Support

Technical information

Design	3-ply
Coating weight per m²	116 g
Length of roll	50 m
Roll width	3.0 m
Area	150 m²
Number of rolls per pallet	46 PCS
Material	PP - Polypropylene
Min./max. temperature resistance	-40 to 80 °C
Building material class/conditions	E - Normally inflammable / in accordance with DIN EN 13501-1
Air layer thickness equivalent to water-vapour diffusion/conditions	2.52 m / in accordance with EN 1931
Resistance to penetration of water	W1
Resistance to tear propagation (longitudinal)	220 N
Resistance to tear propagation (transverse)	200 N
Longitudinal tensile force per 50 mm	347 N
Transverse tensile force per 50 mm	321 N
Colour	White
Width	3 m
Sustainability	Pollutants / Emissions

Documents

Product information

Datasheets (0)

Certificates/ Documents (0)

Accessory

Additive article:

Product

Description

Quantity

Price
/PU

Connection adhesive ALL-IN-ONE

CONADH-(ALL-IN-ONE)-310ML

Art.-no. 0893700111

For the permanent sealing of all connection joints to ensure that they are air-tight and windproof and for fitting indoor and outdoor windows and doors.

Adhesive sealing tape EURASOL<SUP>®</SUP> PLUS

Adhesive sealing tape EURASOL® PLUS

ADHSEALTPE-1SIDE-(EURASOL-PLUS)-60MM

EURASOL

Art.-no. 0992710060

Special adhesive tape for corner bonding and edge bonding

x 6 pcs

Hand-held stapler HT 34

HNDTCK-HT34-(6-14MM)

Art.-no. 0714834

High-performance manual stapler for staples up to 14 mm long

x 1 pcs

Hammer tacker ST 54

HAMTACK-(STAPLE10-14MM)

Art.-no. 0714854

Robust professional tacker with ergonomic handle for staples up to 14 mm long

x 1 pcs

EURASOL<SUP>®</SUP> PE nail sealing tape

EURASOL® PE nail sealing tape

NLSEALTPE-PE-3X60MM-30M

EURASOL

Art.-no. 0875851160

Tested, one-sided adhesive sealing tape for rainproof sealing of nail and screw penetration points on underlay membranes and roof protection films. EURASOL is ideally suited for use with WÜTOP Trio and WÜTOP Trio Plus/SK.

x 5 pcs

WÜTOP<SUP>® </SUP>film adhesive According to DIN 4108-7/SIA 180

WÜTOP® film adhesive According to DIN 4108-7/SIA 180

ADH-ROOFSHT-WUETOP-310ML

Art.-no. 0893700100

Tested system adhesive for permanent sealing of vapour retarders/barriers indoors without a clamping batten

WÜTOP® film adhesive According to DIN 4108-7/SIA 180

ADH-ROOFSHT-WUETOP-600ML

Art.-no. 0893700110

Tested system adhesive for permanent sealing of vapour retarders/barriers indoors without a clamping batten

x 20 pcs

EURASOL<SUP>®</SUP> adhesive sealing tape

EURASOL® adhesive sealing tape

ADHSEALTPE-1SIDE-EURASOL-60MM

EURASOL

Art.-no. 0992700050

Extremely adhesive, versatile adhesive tape for air- and wind-proof bonding of roof underlay membranes, vapour barriers and vapour retarders and for airtight joint adhesion of OSB panels.

Adhesive sealing tape EURASOL<SUP>®</SUP> MAX

Adhesive sealing tape EURASOL® MAX

ADHSEALTPE-(EURASOL-MAX)-60MM

EURASOL

Art.-no. 0992710160

Particularly adhesive, UV- and weather-resistant adhesive tape for airtight and wind-tight bonding of underlay membranes and roof protection films, vapour barriers, vapour retarders and façade membranes.

x 6 pcs

EURASOL<SUP>®</SUP> Thermo HT adhesive sealing tape

EURASOL® Thermo HT adhesive sealing tape

ADHSEALTPE-EURASOL-THERMO-HT-60MM

EURASOL

Art.-no. 0992720060

Adhesive sealing tape with extremely high adhesive force for demanding air- and wind-tight bonding both indoors and outdoors. Strong adhesive film adheres permanently to many substrates, in particular Wütop thermal membranes.

x 10 pcs

Adhesive sealing tape EURASOL<SUP>® </SUP>P

Adhesive sealing tape EURASOL® P

ADHSEALTPE-1SIDE-(EURASOL-P)-60MM

EURASOL

Art.-no. 0992810060

High-quality, paper-based adhesive tape for indoor use for permanent airtight bonding. Protects against moisture and mould growth in the insulation. Ideal for ecologically friendly construction.

x 6 pcs

Adhesive sealing tape EURASOL® P

ADHSEALTPE-1SIDE-(EURASOL-P)-190MM

EURASOL

Art.-no. 0992810190

High-quality, paper-based adhesive tape for indoor use for permanent airtight bonding. Protects against moisture and mould growth in the insulation. Ideal for ecologically friendly construction.

x 2 pcs

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).