Veneer glue
Veneer glue
VENERADH-12KG
Register now and access more than 125,000 products
Short pressing times for relatively long processing time
Ideally suited for veneer work
Easy to pour
By screwing on the glue pouring tap, you can dispense the 28-kg container cleanly and simply into the glue bottle or the glue roller.
No nasty odours
Formaldehyde-free D2 dispersion glue
Universal application
Excellent application behaviour in glue application machines and during manual glue application.
High adhesive quality
Hardened glued joints are viscoplastic. Reliable gluing of all veneer types. Good staining on veneers. Causes no discolouration.
Complies with stress group D2 in accordance with DIN/EN 204
When using highly absorbent material and low pressing force, a relatively large quantity of glue must be applied. The higher the pressing force, the smaller the required application quantities. With large-pore veneer, a thin layer of glue must be applied to prevent the glue from bleeding through. Glue bleed-through may result in colour changes during staining, as the pores in the veneer are already filled with glue, thereby preventing the stain from penetrating the surface. Due to the tannic acid of the wood, the impact of bare metal may result in blue discolouration, especially with oak. At a pressing temperature above +50°C, brown discolouration may occur with softwood veneers. Fresh splashes of glue can be removed with water. Stir glue thoroughly before application and always close container tightly after use. Protect from frost. The processing time and the setting time are highly dependent on the working conditions, e.g. the temperatures, moisture levels and absorption of the materials, application quantities and tensions in the material. The adhesive can be defined as formaldehyde-free insofar as no formaldehyde is used during production. However, extremely small quantities may occur during polymerisation due to secondary reactions. Würth glues may only be used for non-load-bearing applications.
The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.
Datasheets(X)
The veneer adhesive is very well suited to veneer gluing on chipboard, wood core plywood and MDF panels. Surface gluing of laminated panels (HPL panels) on wood, chipboard and MDF panels. Surface bonding, doubling of engineered wood and surface coating of e.g. cabinets, interior doors, kitchen worktops, door frames, tables or corner benches. Complies with stress group D2 according to DIN/EN 204 for gluing indoors with occasional brief exposure to water flowing off or condensation water.
The base material must be free from dust and grease, as well as free from all kinds of dirt that could compromise bonding. The optimum wood moisture is between 8 and 12 %. Apply an even layer of glue on one side with a brush, spatula or glue roller. For more information, please refer to the technical data sheet.
Chemical basis | Polyvinyl acetate dispersion |
Container | Bucket |
Weight of content | 12 kg |
Stress group | D2 |
EN standard | 204 |
Colour | White |
Density | 1.1 g/cm³ |
pH value | 5 |
Min./max. processing temperature | 18 to 20 °C |
Min./max. open time /conditions | 10-14 min / at 20°C and 150 g/m² |
Min. film forming temperature | 5 °C |
Max. temperature resistance of the hardened material | 80 °C |
Min. proportion of solids | 45 % |
Min. room temperature, material temperature and glue temperature | 18 °C |
Min./max. wood moisture | 8-12 % |
Min./max. application quantity in surface bonding | 100-300 g/m² |
Min. application quantity in assembly bonding | 120 g/m² |
Max. application quantity in assembly bonding | 160 g/m² |
Min./max. application quantity in assembly bonding | 120-160 g/m² |
| Minimum pressing times* | ||
| For surface gluing | At 20°C | 15-20 min. |
| At 50°C | 5-10 min. | |
| At 80°C | 1-5 min. | |
| For veneer gluing | At 20°C | 10-15 min. |
| At 50°C | 5-10 min. | |
| At 80°C | 1-5 min. | |
| * The minimum pressing times are for the application conditions specified above. Deviations from the application conditions may decrease or increase the pressing time. | ||
Select RAL-colour code
!! NOTE: On-screen visualisation of the colour differs from real colour shade!!
Last viewed
Die For standard metric ISO thread HSCo Multi Performance
Slotted cheese head DIN 84, brass, plain
Hexagonal bolt with shank
Shoe laces Uvex 9599
EPS profile double cylinder
Fishplate bolt
Door handle pair AL 120, U shape
Workshop scheduler, five rows DIN A4
Work jacket
Hexagonal bolt with shank and fine thread DIN 960, steel 10.9, zinc-plated, blue passivated (A2K)